Strike Eagle's cockpit

Workstations for the pilot and gunnery officer

Where did you start the assembly on all the planes but the cockpits? Over the years I've assembled a few airplanes, but still the fact that you were to build and paint a thing way before you continued with the majority of the build was weird to me. With my skills, and, shall we say limited amount of ability to nitpick about the details of airplanes, no one would probably notice if I just built everything and only then painted what could be seen.

Despite thinking of this I obeyed the instructions like a polite modeler and built what my limited sense told me to build in the first stage. That was the tub, and then the two ACES II ejection seats for both crewmembers.

When the glue had flashed I painted what I could or what made sense to paint at this point. As the interior colour I used the first grey I hit my hands on, Vallejo's Stonewall Grey (VGA 72749). The little panels I painted following both their shapes and the instructions, using Black Grey (VMA 71056).

Without any funky tools I had to paint the ejection seasts in two parts to avoid hitting my fingers into wet paint. The frames of the seats I painted with the dark grey, those ejector triggers with yellow ochre (VMA 71033), and the padding with sand yellow (VMA 71028).

While the previous stuff was drying I painted the instrument panel bits that were still on the sprues. I thought that this way I wouldn't be throwing them around tables and floors while painting. As the basecoat I used the same stonewall grey with dark grey panels where the instructions guided me. Had I been more in the mood, I'd masked the panels off and airbrushed instead, but this scale didn't call for that level of detail in my books.

When I got to it I drybrushed the dark panels with the lighter grey. Once again I was shown that when the drybrush brush seemed to be dry against the paper towel, it wasn't still clean enough. The plastic caught paint so much easier than the paper.

When I returned to the ejection seats I painted the missing parts and added dark green (VMA 71094 Green Zinc Chromate) bits to the seats. And when they had dried, I drybrushed the metallic parts with steel (VMA 71065).

While drybrushing I also poked at the cockpit tub, I mostly concentrated on the pedals and the edges, then I also touched up the instrument panels to highlight the beveled edges of the panels. Before the paint was dry on my non-palette I also painted the HUD's projector plate with steel in preparation for the future.

Now that I got up to speed with the green paint on the seats I mixed some of  that to the dark grey and used it on each of the MFDs. Had I planned this in advance, I'd prepared them all in flat black or dark grey for the screen edges. Well, maybe I remembered that when I worked on the other two F-15s later on.

I had to confess now that had I not got so excited about the jeweling on the 'Mechs and their cockpits, I most likely would never had gone any further than this on these so-called more serious models. But here we were, and I painted a lighter green blob into each panel's lower corner and then the white anime reflections to opposite corners. Not that anyone was ever going to see that in the finished model.

Assembling and painting a bit more

Now I glued the ejection seats into their places, and I had to doublecheck that yes, they did sit that high up. Or the armrests were that low. I also glued the pilot's joystick to stand happily in its place, in as neutral a position as I managed. After that it was the time to install the IPs. The plates fit in just nicely, which made me happy.

After a bit of flashing time I glued the covers over the instrument panels. They most likely had some spots left to fix, but this was easier than swearing with the glue-paint mess the older approach would've caused. As long as I realized to fix them in time, that is. Now I had a good moment to apply a bit of Vallejo's gloss varnish on the displays, later on it would've been way too bothersome.

The steel layer on the projector was now dry, so I stippled some Citadel's blue wash on it (Drakenhof Nightshade). When that had had a moment to cure, I stippled around and near it some violet (Drukii Violet). That didn't give me an iridescent rainbow, not even close, but it was more than I had ever thought of doing for a HUD. If the Citadel's green wash that I had bought in the late half of the '90s was still alive, I'd maybe use a drop of it as well but I wasn't counting on it.

Well well well, the Green Wash I bought at some point between 1996 and 1998 was still as good as ever, at almost 30 years on the planet. I stippled some of it on the projector to see how it behaved.

Now the office spaces were just about done. I did install a handle-thingie on top of the gunnery officer's IP cover. Then I had just the throttle lever and the bomber's three joysticks and the HUD screen left. I really didn't know what the rear seater did with those sticks but my uneducated guess was "everything".

After the installations and paintings of said controllers was done I marked the correct places on the hull for the tub's gluings, and then painted the remaining inner walls with light grey. While looking at photos of F-15E cockpits I realized that the ejection seats had to have green gas bottles on the lefthand sides of the seat frames. I checked that they had indeed been modeled on, and painted them light green (VMC 70942), grumbling that I hadn't noticed them earlier.

Based on a pretty quick ddg search those were emergency oxygen tanks. I was just left thinking if I ought to paint those tubes going out with rubber black to make them look more correct than this metal-drybrushed things. Anyone reading my nonsense had to know by now that if I was poindering it out loud, i was also just about to pick a paintbrush up.

Tub sealage

The inner tub walls were painted with the same colour as the cockpit details. No details had been omdeled on the inner walls, no panels or anything, so I didn't start freehanding or modeling anything from scratch.

With the paint dry I drilled the instruction-demanded holes with my finger drill, the insides of the halves had nice indents for the upcoming holes. Based on a dry-fit the tub fit nicely inside the plane's hull parts, and it got glued in tight into the right half. After a bit of curing I glued the left half on the rest, and squeezed the setup tight together. Finally I taped a couple of parts together while waiting for the next modeling session.

I was really thinking that the cockpit had to be pin washed, but I wasn't sure of the order of business. Another question, very much related to this, was when should the HUD plate be glued on. Should I glue it on right now, or after the oil wash round to avoid funny-shaped lumps? The latter option sounded cleaner to me.

While pondering I checked the instructions ahead and realized that when the cockpit canopy was to be glued on, a couple of pieces needed to be glued into the canopy par, and I had not prepared those pieces yet. To avoid another forgetful moment I painted them now with light grey. This gave me the thinking time to decide that I would do the pin washing when the nose was installed into the body of the plane, and after that I'd glue the HUD plate on. This might also prevent any accidental "whoopsies" moments with the loose cockpit subassembly.

Halfway to thirty

 

Riding the wave of puberty

An old fart was remembering himself at fifteen, when I was on the last year of elementary school: this view we nerds mocked with whenever subjected to a family computer running the latest from the foul B. Gates and his company. Just like with ie where your only task was to download a proper browser, the first thing with Win95 you wanted to exit it to do something, anything.

Some things haven't changed in these decades, my loathing of Windows has remained strong :D Project Mumblings and its Finnish-speaking sibling haven't been quite as annoying as I was at the same age, at least I hoped my verbal output has improved a tiny bit during their 15 years. 

A rarity these days: Panzerkampfwagen

The semi-accidentally bought Panzer IV Ausf. F2 by Border Model was a really nice set, and like I praised them while working with them, the Panzerwerk Design tracks were great and I wanted more for my next tank. As soon as I figured out what that was going to be, got one bought, and started assembling.

Lego

The Bumblebee got bought primarily because I wanted to do my part to ensure more Transformers lego sets in the future, not really because of the character itself. Still, the set was fun and supported my childhood memories, and this was about a quadrillion times more cool than the flea market -found and equipmentless G1 Bumblebee.

Last Autumn's father's day arrived with more buildables. Executor was also glorious, and actually fit somewhere, unlike the large ISD that was waiting for space and time inside its box.

Fresher stuff, Soundwave was orderable on 1.8., and as it was known, I ordered it the very morning. I could've started my first post-vacation morning a lot worse. That, of course, didn't make the waiting any easier or nicer. Luckily Soundwave was delivered right at the end of my second workday so I could start that evening already.

Rocket launcher diorama

As anyone knew, I hadn't made practically any dioramas. Generally speaking I had no materials, tools, nor even ideas - not to mention space - for making display things for my constructs. Maybe the airplane stands like Focke-Wulff's grass field with a Kübelwagen, the Fulcrum's much-suffered Soviet concrete base, or the Flanker's flight stand could be called vignettes, even if the difference between the two was a bit funky. This setup was the first one in ages that felt that it would justify a somehow fancier title.

Urged on by my colleagues I started on it, but I had to admit I didn't really need much poking to get going. My absolute amateur skillset glared a viewer from here and there, but the main thing was that I had a good time and I was generally quite pleased with the time-consuming thing.

Mechs

Last rolling year had been nicely loaded with plastic 'Mechs. Five different sets, fifteen minis from scratch, and five with a repaint of cockpit panels, energy weapon lenses, and Jump Jets.

Ghost Bear

Two final Points for the Star from Delta Galaxy, a Stormcrow and a Viper:

Jade Falcon

Retouching the Operation:REVIVAL Star, meaning Executor, Puma, Timber Wolf, Nova, and Mongrel. This improved my somehow annoying day by a factor of craploads.

 

Otherwise heavier hardware: Warhawk, Turkina, Ebon Jaguar.

 

 

Blood Spirit

Funnily enough I forgot to take a final group photo of the Star that was for the Clan that turned the practical opposite of the so-called espirit de corps. Clan Blood Spirit, Alpha Galaxy, unspecified Cluster, Trinary, and Star: Mist Lynx, Kit Fox, Stormcrow, Ice Ferret, Shadow Cat.

Jade Wolf

Some Second Line ClanTech BattleMechs for a very short-lived Clan [in an inverted N-pattern from rear left to front right]: Marauder IIC, Warhammer IIC, Stone Rhino, Hunchback IIC, Supernova.

Queue

In addition to the digital stuff I also had a couple of bits in the Clan Invasion box, and then all that came in the awfully-long-awaited Mercenaries KS loot. Nope, I was not going to run out of BT stuff in the backlog, which meant that at my rate of painting there could be stuff for a couple of years. The previous ones have been in slow progress over some years, so the assumption was indeed years.

BTTracker

I have been randomly and casually improving my tracker, at least whenever I noticed that some earlier solution turned out to be too clunky. Not that it interested anyone else in the known universe, but I was thinking of posting about it at some point anyway. That one made my hobby life easier and that pleased me, even if a smarter and so much more time-efficient approach would've been a super simple UI and a db model.

Air farce

This I have said often, that I have never been that much into planes, especially anything more modern than a Me-262. Still, I was beside myself when Santa brought me an F-15 and I even managed to start on it before the following Saturnalia! In the name of science it might be fun to get the other two F-15 models from different manufacturers just to compare them.

Games

Since the last anniversary post my Steam Deck has been graced by the Doom set (having bought the original at some point I got an autoupdate to DOOM + DOOM II which then also included Final Doom, Master Levels, Sigil and couple of others) from start to finish; I played through the Duke Nukem 3d's four episodes, of which the last was completely new to me; some more Mechwarrior 5: Mercenaries that got somehow stuck with my mod setup and I just uninstalled the damn thing in annoyance; then I returned to Factorio v2 in the late winter.

For some unexplicable reason I started working on the Lazy Bastart achievement in  Factorio, which meant I could only build a minimum amount (<= 111 entities) of anything by hand, and everything else had to be done with assemblers. This time I started with a Main Bus straight away (8 for metal plates, 8 for copper plates, 2 for steel beams, 1 rock/brick, 1 coal, 4 green circuits, 4 reserved for upcoming products) that also took a bit of extra time because I had to tweak and poke around constantly, but at least it kept the spaghetti at bay. Unless you looked at the smelting area I built into a bit too tight a spot for extensions, which I refactored into tidy input-output lines took the evenings of a week.

My slow tinkering then kicked me in the shins when my sisteen smelting lines with roboti arms, and their neighbouring 20 centrifuges choked my six steam engine parks. I had to do some emergency extensions until my factory had the four nuclear reactors and their accompanying bits constructed for me, which then moved my energy worries to a more distant future. The beauty of this kind of planned automation was that even if it took a while, even the resource-intense things got built while you did something else. In this very practical case the fission reactors, heat exchangers, and turbines had been ready for a while and I didn't need to start building them when I finally I knew I needed them.

Pretty soon after that I noticed how my 24-lane Main Bus was too narrow after all and I needed four more lanes (2 red circuits, 1 blue CPU, 1 sulphur) and I tried to get the liquid pipes also somewhere so I could move the lubricant to the CPU subfactory and the electric motor factory on the opposite side. The next time I'd start with even more pre-planning and at least eight lanes more to start with a round 32 width.

Despite all this silliness I got my rocket factory started and had them launch rockets with satellites at a calm pace, after assembling only 103 items myself. In comparison to a normal game the early part was noticeably slow and hand-holdy, because I had to carry materials back and forth and change the recipes of my few Assemblers until my setup had reached the critical mass and I could just collect the technomechanical fruits from the containers.

Cyberpunk 2077 had fallen off my interest list because I simply didn't care for one-expression Reeves' prominent presence. The ~5 years of reading/hearing people's praise of the game, Steam Deck support and new big updates got me over my grumpiness and I bought the Ultimate Edition from some Spring Sale.

Creating a character took just about all of my playtime for my first gaming session, as these things tended to go, and I wasn't in a rush in this new world. I chose Nomad as the background, jumped into the First Act which was a long intro to the game. It took me over a week, about 10h, and then I stepped into the actually open world. The last time I played anything similar was Fallout 4 (311,5h for a single but pretty thorough playthrough about nine years ago), so I didn't have much to compare to.

By the midsummer week I had continued the main story only by meeting that one dude in a café, then I did what I always did in RPGs: side quests, subside quests, minor quets, look a squirrel! until there's nothing until the big story has been kicked a step forward. One evening I was greeted by an achievement pop-up: street cred capped, and I hadn't even paid any attention to it yet. So far I had done all the tasks in the Center, and continued southward to Heywood where I moved a bit further to Pacifica and even Westbrook to just solve things and simply drive around.

By the summer vacation in June I had spent a silly amount of time just running around, solving mysteries, and I still hadn't progressed in the story. Had I even been near the fence I was supposed to lean on to meet the guy? Doubtful.

Between the vacation and today's Project Mumblings birthday I completely cleaned up Westbrook, Watson, Santo Domingo, Heywood, and Badlands of gigs and NCPD tasks. I even spent a moment with Takemura at some point, and then left him to wait for a better moment again. Last weekend, having done everything else I practically found on the map, I started some mission chains for both Judy and Panam. No idea where those were headed yet.

My Doom story generator and the pygame proejcts have been on hold for a bunch of years now, even though I did poke my generator's texts at some point. Nothing to warrant sharing, though. Maybe I should just sit down and go through all the sentence constructors and then continue on to something more exciting or silly.

Project V/25

Revell F-15E Strike Eagle

Santa brought me both a Panzer Aces set of paints and surprisingly, a 1:72-scale F-15 that I had wished for, and this was a subtype E. I didn't mind the config myself, and this was the first of the three F-15s I wanted to implement a funny (to me) idea.

This multimodel main project affected how I was going to handle the documentation of this first plane.

Most probably I'd go with a build, cockpit painting, and the priming, maybe even the basecoating of the plane would be included in IV/25, then it would be stored until the other two would have reached the same stage. At that point, with the triplet in the place where they'd diverge, I could do the actual paintjob as its own subproject.

Optionally I'd do this one from start to finish but just skip sharing the paintjob until I was far enough with the others. Some basics I would need to paint in a recognized and proper way anyway, like the titanium engine cowlings and whatnot.

Instructions

On a cursory glance the coloured instructions were pretty clear, I appreciated the colours supporting the A-Z flags. Especially the colouring of the weaponry was a very nice detail. Was I going to bother following those? We'd see.

Bits

There were three transparent pieces this time, the canopy bits and the collector plate for the HUD. Maybe I ought to paint the sides with a coloured wash instead of doing them black. I had to look into that stuff, as I had no clue right now.

All I could say about these was that they looked like pieces of an airplane.

Miniproject IV/25

Lego 10358 Soundwave

From rumours to actual items

I started hearing some whispers of the next Lego Transformer during H1/2025 and these whispers said it'd be Soundwave. This got confirmed before my summer vacation and it'd also have a sound brick and of his minions we'd get Laserbeak and Ravage. On the e-shelves it'd be on 4.8. unless you were an insider, you'd get to send them money on 1.8. already. Conveniently that was also the day when I returned from my vacation, absolutely perfect timing for a change.

Then all I could do was to wait for the delivery. Luckily there was the weekend, and a long enough way home, so I got enough things to keep me busy and away from fretting.

This time the express shipping was truly express

Early on Monday I got a message telling me they'd actually deliver it by the end of the day. That was a bit ambiguous but I was prepared for much worse. During my morning meetings the delivery window got specified to 13-15, and it was a timeslot I was meeting-free! The driver ended up having some trouble somewhere, so it was a bit later when I got the box, but I was so excited I didn't even think of grumbling.

Construction in three evenings

One and half a thousand pieces in twelve numbered bags required some time to assemble. As always, working on doubles the first arm/leg/whatnot was half as quick to build than the follow-up(s).

Mini-me

The bag number one gave us Soundwave's alt mode and two printed different minion tiles on the deck. Genious.

Laserbeak

Bag #2 had the bits for Laserbeak. Just the printed 1x1 tiles with the Decepticon insignia made me giggly. The lego version wasn't quite as complex as the Masterpiece versions so the engine-gun pieces had to be detached when transforming to the alt mode.

Ravage

Third up, Ravage. Ravage's engine things were detachable for the transformation as well.

They were magnificent! And that's as far as I got on Monday, but I wrapped up in good spirits.

Soundwave

On Tuesday I got to start on Soundwave's hips. Behind the now-fallen Play button we had a cavity for the sound brick. The infamous sound brick that I hadn't encountered yet.

Ah, the sound brick was immediately in bag #5, and over it I built a nice face mosaic. In the name of transparency, I may have spent a stupid amount of time playing with the sound chip. There was a silly amount of sounds in it, more than I felt like counting. The list contained some pew pew effects, the transformation sounds, the scene change jingle from the cartoons, and a pile of Frank Welker quotes such as "Soundwave superior". The rest of the family wasn't quite as extatic as I was.

Over the sound brick I built a chest cavity, with enough space for one minion at a time. The instructions said that the opening mechanism was the first thing they engineered.

This glorious Decepticon-decorated transparent bit was in a separate bag to avoid scratches. Now that I got another bagful of pieces assembled, the cassette bay door and its opening mechanism worked. Satisfying was the perfect word here, both for the tactile feel of pressing the button, and the sound that it made.

Interestingly the remaining pieces of this bag brought the craftily hinged bits where the arms were going to be attached to.

Now the next bag (I guess I was on the seventh now) gave Soundwave his arms. He had four fingers per hand, and they all were articulatable unlike Optimus Prime's sausages. In addition to the usual finger-pointing and fist-shaking he could do the heavy metal horns or just flip the bird. Or both at the same time. The limbs also had an amount of ball joints so they were going to be very nicely poseable.

On Wednesday I returned to the build and started with the right leg. The inside of the calf got a funky multi-jointed himmel, whose functionality only started being clear when the whole leg was closed and the sides encased the mechanisms properly.

\,,/ Rock rock \,,/

While in progress the spurlike thing was a silly floppy thing that didn't feel like it had a good real position. 

After smashing the missing leg into his hips I was already sadly far in the building proess. I didn't even think of checking if Lego Soundwave could press his own shoulder button as coolly as MP-02 could.

I had been wondering why I had to press the front faces of the legs into the leg itself as if I was partially transforming him into his altmode. Still, I obediently followed the instructions. The reason became clear after the next bagful of pieces and the subprocess of building the feet of his. Those were easy to press into their places when the receiving ends were in a sturdy position. After setting them in place the feet were then folded out for a proper standing robot pose.

The last two bagfuls and steps gave us Soundwave's head and the head's hideout in his upper back, and the AA batteries / weapons. The final bag just had the Icons set's plaque. At this point it was a bit late and I was both excited and busy, so I didn't take too many WIP photos.

For his optics I was given two options: red ones like in the early episodes, or yellow. Instead of choosing randomly, I checked what MP-02 had and installed the yellow lenses.

Naturally I tried out the alt mode and its transformation process. It worked very nicely, thanks for asking.

Photoset - coming soon :tm:

Very much unlike my usual approach to this, this time I didn't wait to get the light tent, tripod, camera, image editors and all set up and done before sharing this post. So for a change the photos were going to be dropped in afterwards. All the essentials were already shown, so only silliness remains.